______ ∙ ° ___∙ ____ ∙ _____ ____
° / __ \ ∙ ___ ∙ / / ∙∙ /___ \ ° / ___//___ \
∙ / / / / ______/__/ _____ / /__ __/ / / /_ __/ /
/ /∙/ / / / / / / __// __/∙ / ___/ / __ \ / ___/
/ /_/ /_/ / / /_/ /__/ \ / /___ __∙/ /_/ // /___∙
∙ \________/\____/\___/\____/__/__/ /_____//_//_____//_____/∙
∙ _______ ∙ ∙ ∙∙ ___
∙ / ____/ Spectre/Optical Brothers present: / / ∙ ° ∙
° / / ∙ _____________ °_______ __________ ∙___/ /__________
/ / ∙ / / \/ \/ / \/ / ___/ __/
/ /____/ / / / / / / / / / / / / / / ___/ / ∙
\______/_____/__/__/__/__/__/__/\____/__/__/\____/________/ ∙
___________________________________________________________
┌──────-─-─-─-─-----
│ Quick Commander
├─────────────────────-─-─-─-─-----
│ Based on boot by Max Petrov, 1996
├─────────────────────────────────-─-─-─-─-─------
│ User's manual (english edition by Mac Buster)
└─────────────────────────────────────────────-─-─-─-─-─------
For those who sees Quick Commander for the very-very first
time: Quick (it is really quick) works with your floppy disks at
the maximal possible speed and utilises direct access to WD-1793
chip to achieve it. Alas, this means that you can not use Quick
with a hard drive.
In case you've got 16K or 32K of Shadow RAM (a.k.a Cache) you
may load Quick into it and invoke the commander at any moment -
all you have to do is to press the Magic button on your disk
interface. To load Quick Commander into Shadow RAM you have to
press and hold on <I> (first letter for <Install>) button while
the commander is loading. If you see a short green flash on the
border then Quick was successfully loaded and installed into the
Shadow RAM, after the flash you may release the <I> button. Now
you may invoke Quick by a single Magic button hit.
╔═════────────────────────┐
║ Main menu : ║
└────────────────────═════╝
When commander is loaded you will see the main menu on the
screen. Here is schematical illustration of it:
┌──────────────────────────────────────────┐
│A boot ╔═╗╔═╗╔═╗╔═╗╔═╗│ - dives list
│A FUT2.01 ╚═╝╚═╝╚═╝╚═╝╚═╝│
│B EMS 2.55 ╔═╗╔═╗╔═╗╔═╗╔═╗│ - drives list
│C ZXZIPs+! ╚═╝╚═╝╚═╝╚═╝╚═╝│
│D ZXUNZIP! ╔═════════════╗│
│E Click! ║ disk title ║│ - disk title
│F Lara 4.5 ╠═════════════╣│
│G Quick262 ║ Memr:.512K ║│ - available RAM
│ ║ Del:..0 ║│ - deleted files.
│ ║ Free:1411 ║│ - free sectors.
│ ╠═════════════╣│
│ ║ Mrk:..0 ║│ - \
│ ║ Sect:...0 ║│ - are not used
│ ╠═════════════╣│ in the menu
│ ║ Slow save ║│ - /
│ ╠═════════════╣│
│ ║ ╓Spectre──╥ ║│ - authors logo
│ ║ ╙─────2001╨ ║│
│ ╠═════════════╣│
│ ║ ║│ - not used in
│ ║ ║│ the menu
│ ╚═════════════╝│
│ ─═Quick Commander v2.62═─ │
│ 5-reread Name Care Run_48 Tr-dos spc-mark│ - hotkeys list
└──────────────────────────────────────────┘
On the left hand side of the screen you will see names of
BASIC files, one filename will be marked by cursor bar. Use <Q>,
<A>,<O>,<P> and <6>,<7>,<8>,<9> buttons to move the cursor bar.
Press <0> or <ENTER> to start file under the cursor bar. Also
you may start a file by pressing a button with letter which is
written on the left hand side from the filename along with <Caps
Shift> (some files can be started without <Caps Shift>). For
example: to start file "ZXUNZIP!" file from the illustration you
have to press <Caps Shift>+<D>. Quick Commander will load and
start file using its own routines, this allows you start files
with absolutely equal names from the _same_ disk. At the bottom
part of the screen you may see hot-keys list of the commander,
e.g. to start a file in 48K-only mode you must press button <R>
(the capital letter in "Run_48" writting). Other hot-keys used
in the main menu for following functions:
1,2,3,4 - Select A,B,C or D drive respectively, selected
drive icon will be "recessed" and change its colour to green at
the right upper corner of the screen.
Edit mode (<CS>+<1>) - cycle switch of drive. Press and hold
on the button till desired drive is selected.
Caps Lock (<CS>+<2>) - cycle switch of destination drive. Not
used in this menu.
"5" (5-reread) - reread disk directory.
"N" (Name) - disk rename mode. You may enter up to 11 symbols
for the disk name. Use: <Left arrow> and <Right arrow> to move
the cursor mark, <Delete> - delete a symbol under cursor mark,
<Edit> to switch cyrillic/latin alphabet. <Caps> - switch small
and capital letters of current alphabet. Cyrillic alphabet uses
standard "ЯВЕРТЫ" keymap, letters "ч","э","ш","щ","ю" are mapped
to "a","s","f","g","x" with <Symbol Shift> pressed. <Extend> and
right mouse button used to leave disk rename mode, <Enter> and
left mouse button - to save new name to the disk directory.
"C" (Care) - disk service menu. See detailed description of
the menu above.
"R" (Run_48) - start file in 48K-only mode. It sets 5th bit
of #7FFD port and starts file whose name is undercursor bar.
"T" (Tr-dos) - quick exit to TR-DOS.
"Space" - file service menu.
Move mouse to see second cursor (mouse pointer). Use mouse to
start files - click left mouse button on a file name. Use right
mouse button to mark files to start the file in 48K-Only mode.
Click on disk drive name to change current drive. Click on
"hot-keys" at the bottom of the screen to see options. If your
mouse has a third (middle) button you may use it to reread disk
directory. If your mouse has no middle button you may reread
disk directory by selecting "5-reread" option in the "hot-keys"
list at the bottom of the screen or press one of two "buttons"
at the top right corner of the screen. These "buttons" shown at
the illustration above.
╔═════────────────────────┐
║ File service menu : ║
└────────────────────═════╝
┌──────────────────────────────────────────┐
│boot B .39 ╔═╗╔═╗╔═╗╔═╗╔═╗│ - Source drive
│EMS 2.55 B .97 ╚═╝╚═╝╚═╝╚═╝╚═╝│
│EMSphone p ..2 ╔═╗╔═╗╔═╗╔═╗╔═╗│ - Destination drive
│EMSmacro m .14 ╚═╝╚═╝╚═╝╚═╝╚═╝│
│CoolRead O ..2 ╔═════════════╗│
│ZXZIPs+! B .66 ║ disk name ║│ - disk name
│ZXUNZIP! B .53 ╠═════════════╣│
│EMSsetup s ..1 ║ Memr:.512K ║│ - available RAM
│ZX-WORD O .51 ║ Del:..0 ║│ - deleted files
│BbsPrep O .18 ║ Free:1411 ║│ - free sectors
│userlist S ..2 ╠═════════════╣│
│Driv4.02 C .13 ║ Mrk:..0 ║│ - marked files
│ Click! B 175 ║ Sect:...0 ║│ - marked sectors
│ Click! C 175 ╠═════════════╣│
│Lara 4.5 B .93 ║ Slow save ║│ - Saving mode
│Lara 4.5 W .43 ╠═════════════╣│
│setup p ..6 ║ 20553/16500 ║│ - current file info
│music M .12 ║ ZIP/..9/..6 ║│
│Quick262 B .57 ╠═════════════╣│
│View4.1! Z .60 ║ ║│ - a "window" for an
│ ║ ║│ analyser for Copy,
│ ╚═════════════╝│ Move, Play, etc.
│ ─═Quick Commander v2.62═─ │
│Copy Move Del Ren merGe View muZ m+ m- spc│ - "hot-keys" list
└──────────────────────────────────────────┘
"Slow save" or "Fast save" messages reflect current saving
mode of the commander. "Slow save" mode will work fine on any
drive type. But if you want to increase saving speed in 2 (two!)
times you may change the mode using any disk-doctor (hex-editor)
like Conver vX.XX or Real Commander v1.XX, open first sector of
Quick Commander's BASIC file (Quick262.B) and replace letter "N"
to letter "Y" in line "save: fast = N" and save changes back to
the disk. And after that at every start the commander will show
you "Fast save" message and will work in the "Fast save" mode.
Pay an attention: in "Fast save" mode you may have unstable
writting process on some types of disk drives. After changing to
"Fast save" mode youhave to copy several files to clean disk and
check it with "check" option from disk service menu. Do not use
"Fast save" mode if you have an error message at each 2nd track
while checking the disk by "check" option. Btw - you may
increase speed if you disable "Restore disk" option in "Disk
care" menu.
Under window for "Fast save" and "Slow save" you may see some
numbers - this is information on the file under cursor bar. On
the illustration above there are following information shown:
20553 - start address
16500 - file size in bytes
ZIP - file extension
..9 - number of first track of the file
..6 - number of sector
Move cursor using <Q>, <A>, <O>, <P>; <6>, <7>, <8>, <9>; and
cursor keys (arrows). Use <0>, <ENTER> and left mouse button to
mark filename.
<1>,<2>,<3>,<4> - Select A,B,C and D disk drive respectively,
selected drive displayed as recessed drive icon of greed colour
in right top corner of the screen.
Edit mode (<CS>+<1>) - cycle switch of drive A,B,C,D. Press
and hold on the button till desired drive is selected.
Caps Lock (<CS>+<2>) - select destination drive.
"5" - reread disk directory.
"C" (Copy) - copy marked files. All files will be copied in
the same sequence as they were marked.
NOTE: If you have not enough free spase on destination disk and
you have a "No space" message on the screen, you may leave this
mode only if you press and hold one right mouse button till
"Break, Retry, Ignore, Abort" menu appear on the screen. In this
way you may stop ANY disk operation using mouse. On the keyboard
you may press <SPACE> key to have the same effect, or button <A>
for immediate interrupt.
"M" (Move) - move (pack) free disk space. Will work only if
you have deleted files on current disk.
Copy and Move functions will not work in 48K mode. Commander
uses all available memory of your computer. Detected RAM shown
in the right upper corner of the screen (on the illustration it
is displayed as "Memr:.256K"). The commander can detect and use
following memory extensions: Scorpion256/Kay256 on #1FFD port,
Profi256-1024 on #DFFD port and Pentagon 256/512 on #7FFD port.
In Scorpion256 mode 8ht page (with shadow monitor) will not be
used. You may see progress indicator (squares) in the right
bottom corner of the screen.
"D" (Delete) - delete marked files.
"R" (Rename) - rename file under cursor. Works in the same
way as "Disk rename" in main menu. If you enter a symbol instead
of "grid" in name of deleted file then the file will be restored
(undelete).
"G" (merGe) - "join" marked files. There should not be not
marked of deleted files between files you want to join. If more
than 255 sectors marked then several files will be generated.
"V" (View) - if cursor stays on @-file or on screen$ (6912
bytes lenght) commander will turn into viewer mode. Use <SPACE>
and leftmouse button to change picture colours, <ENTER> - next
file, rest buttons - exit. On any other file than @ and screen$
commander will turn into a text-viewer.
"Z" (muZ) - search in marked file for a music module in
Pro-Tracker v3.x format in a marked file. Module may be compiled
or not, with or without player.
"+" (m+) - select all files (invert selection).
"-" (m-) - unmark all marked files.
<SPACE> - exit to main menu.
After double click on a file name the commander will check is
the file is screen$ or is there are a music module inside. If no
screen$ of music module isn't found, commander will turn to text
viewer mode.
╔═════────────────────────┐
║ Disk service menu: ║
└────────────────────═════╝
Press <C> in initial menu to get into this mode.
"K" (Keep cat) - backup disk directory to 161 track (not used
by system).
"S" (Show) - compare disk directory with backup copy.
"E" (rEstore cat) - put backup directory from 161 track to
0 track.
"C" (Check disk) - fast disk check. If commander finds a disk
error it will automatically try to restore it. Process indicated
by usual "squares" at a corner ofthe screen.
"R" (Restore disk) - restore disk. May also be used to
increase a data transfer speed.
"Check disk" and "Restore disk" may also be started from a
certain marked file.
"F" (Format disk) - format disk. You have to enter name for
the disk (up to 11 symbols). If you do not want to enter new
name (press <ENTEND MODE> or right mouse button, and so on) you
will not be allowed to format disk and will be rejected from
disk format mode. Formatting process will be started right after
you have entered last symbol of the disk name. The process will
be indicated by "squares" in a corner of the screen. REMEMBER:
Quick Commander starts formatting from the LAST track of the
disk, so you have a time to stop process if you occasionally
tried to format wrong disk. In best case you will not loose data
in worst case =:-O... Disk will be formatted for 2544 sectors
(80 tracks, 2 sides).
╔═════────────────────────┐
║ File viewer mode: ║
└────────────────────═════╝
Starting from version 2.2 and above, Quick Commander has an
internal viewer for text files. It uses 64 chars per line (turbo
idea by KSA). The viewer displays files with up to 255 sectors
length. If file has 0 sectors length then 255 sectors will be
loaded into viewer's buffer.
Viewer control:
Line up: <9>, <Q>, cursor up
Line down: <8>, <A>, cursor down
Page up: <True video>, cursor left
Page down: <Inverse video>, cursor right
Move right (up to 2040 symbols): <7>, <P>
Move left (up to 2040 symbols): <6>, <O>
To begin of the file: <B>
To end of the file: <E>
Next file: <ENTER>
Enable/Disable sound thru AY: <S>
Enable/Disable line wrap mode: <W>
Convert text: <C>
Return to commander mode: <Edit mode>, <Extend mode>
Mouse control in the viewer is equal to mouse control in file
mode of the commander. At the bottom part of the screen you may
see another "hot keys" list.
Screen with text virtually split onto four parts:
┌───┬───────────────┬───┐
│ │ │ │
│ │ 3 │ │
│ 1 ├───────────────┤ 2 │
│ │ 4 │ │
│ │ │ │
└───┴───────────────┴───┘
Click on 1-st area to move text one page up. Click 2-nd area
to move text one page down. Click 3-rd area to move text one
line up. Click 4-th area to move text one line down.
Text converter (hot-key <C>) used to convert text from one to
another text encoding standard, you may see: windows (Win-1251),
KOI8-R, DOS (CPP-866) standards.
Line wrap mode (hot-key <W>) can be enabled/disabled by
option "wrap". The mode is useful for texts with long lines
(over 64 chars). When the mode is on options "Left" and "Right"
will not work and also tabs are ignored.
________________________________________________________________
Thats it. Sends your offers, ideas, moneys, alive credit card
PINs, keys-from-an-appartments-full-of-money (with addresses of
course), parsels, letters, and so on to my e-mail:
E-mail: spectre_ob@euro.ru
On official home site of Optical Brothers group you always can
find recent version of Quick Commander, also you can leave some
lines in phorum, and have some chat with author of the Quick:
http://www.opticalbrothers.f2s.com
Bye!
Spectre/Optical Brothers